| NANDA |
Xerun 80A Brushless ESC for 1/8 Scale Car |
540L KV2150 Brushless Motor
|
| G.T. POWER |
GT POWER XDrive 6 Charger/Discharger
Microprocessor
controlled high performance rapid charger/discharger for Lilo/LiPo/LiFe/NiCd/NiMh/Pb
batteries.
Four independent output with four independent display!
-
Opearating voltage range : DC 11-18V
-
Charge Power : max.60 watts per channer
-
Discharge Power : max 5 watts per channel
-
Charge current range : 0.1-1A per channel
-
Discharge current range : 0.1-1.0A channel
-
Cell Count: 1-15 NiCd/NiMH Cells, 1-6 Lilon/Life Cells, 1-10 Lead-Acid Cells (2V-20V)
-
Currrent drain for balancing Lithium : 300mAh/cell
|
GT-Power A606 (50W)
Max 6A Balance
Charger Discharger
6AMP
-
Digital Intelligent Multifunctional Balancing Charger/Discharger/Cycler
LiPo, Li-lo, Li-Fe (A123M1),
Ni-Cd, Ni-MH, Pb (Lead Acid)
Operating Voltage Range: DC 10 - 18V
Circuit Power: Max. 50W for
charging, Max. 5W for discharging
Charge Current Range:
0.1 - 6.0A
Discharge Current Range: 0.1 -
1.0A
Current Drain for Balancing::
300mAh/cell
NiCd/NiMH Battery Cell Count:
1 - 15 Cells
Lithium Battery Cell Count: 1
- 6 Series
Pb Battery Voltage: 2 to 20V
Dimensions: 137mm x 98mm x
30mm
Available with optional 5A adaptor
|
GT-Power A606-D
AC/DC Charger
Operating voltage range: DC 10.0-18.0V ,
AC 110 - 220V
Circuit power: max.50Watts(charging) max.5Watts(discharging)
Charge current range: 0.1-6.0A
Discharge current range: 0.1-1.0A
Current drain for balancing LiPo: 300mAh/cell
NiCd/NiMH battery cell count: 1-15cells
Lithium battery cell count: 1-6 series
Pb battery voltage: 2-20V
Dimensions: 135×149×40mm
|
GT-Power X6
LiPo Pro Charger
Graphical Display Balance Charger
up to 7A and 80W output
- Digital
Microprocessor Controlled Multifunctional Balancing Charger/Discharger/Cycler
LiPo, Li-lo, Li-Fe (A123M1),
Ni-Cd, Ni-MH, Pb (Lead Acid)
Operating Voltage Range:
DC 11 - 18V
Circuit Power: Max. 80W for
charging, Max. 5W for discharging
Charge Current Range: 0.1 -
7.0A
Discharge Current Range: 0.1 -
1.5A
Current Drain for Balancing::
300mAh/cell
NiCd/NiMH Battery Cell Count:
1 - 17 Cells
Lithium Battery Cell Count: 1
- 6 Series
Pb Battery Voltage: 1 - 12
Cells
Dimensions: 135mm x 100mm x
24mm
Backlit LCD Display : 128x64
pixels |
AC 5A Supply Adaptor for Multi Charger
Input voltage range: 100-240 volts AC
Frequency & load: 50/60 Hz 1.5-amp draw max
Output: 12-volts 5-amps max
|
GT
Power 600w 17V 36APower Supply
Input Voltage: AC 100-230V
Output Power: 600W
Output Voltage: 17V
Output Current: 0-36A |
GT Power Multi urp
Show total voltage of the pack
Show Individual cell voltage
Balance cells.
Discharge to specific voltage
Also can measure Rx battery with
Futaba plug Specification:
LiPo/LiFe 2-6 cells
Receiver battery 1.2v - 8.5v
Balance voltage setting range: 2v - 4.2vDischarge voltage serring
range: 2v - 4.2v
|
GT Power Servo Tester
1.In three modes to check servos
or ESC:
---Manual mode---- Turn the knob with different speed. Check the
reaction time.
---Neutral mode----Make the servo go back to the neutral point.
---Automatic “window wiper” mode-make the servo swing like
window wipers in the biggest angle.
2.It can connect 1-3 servos
simultaneously and test such as 1-3 servos consistency and so
on.
3.You can also connect 1-3 ESC to
test and compare their reaction time respectively.
4.It can connect 3 servos of the
CCPM helicopters, adjust the helicopters and select servos.
5.It can also connect the servo
of airplanes. Install the steering-box and adjust planes by
using such as the neutral mode and so on.
|
GT Power
5A UBEC
- 'Switch mode' DC regulator that
takes the high voltage (up to 42 volts) of the main battery pack and
converts it to a consistant and safe 5 or 6 volts (selectable) for your
receiver and servos.
Input Voltage: 8 - 42V (3 - 10 cells
lithium battery pack) Output Voltage: 5V or 6V(Changeable with an
jumper) Current: 5 Amps continuous 7.5 Amps burst |
GT Power Digital Lipo Battery Meter
Measure
Li-Po from 2-6 cells
Continuous readout of battery being measured
Reverse polarity protection
Total voltage of the battery pack can be measured
Highly accurate (0.05V)
Compact in size: can be put in microheli or other models
Light weight (6g)
Dimension: L51.5x W19.8x H10.05 (mm)
|
GT Power Flight LED System
1. Input voltage: 4V-6V
2. Current: 30mA
3. Main control board size: 35×24×8mm
4. LED lead length: 600mm/pc
5. Weight: 35g
|
GT
Power RC Car Flashing Light System
1.
Car LED ×12 pcs.
2. Car LED holder ×12 pcs.
3. Control box ×1 pc.
4. Power connection.
5. Control connection.
6. Accessories parcel .
|
GT Power RC Car LED System
1. LED System Control Box x 1
2. Y-Shape Cable x 2
3. 5mm White Light Set x 1
4. 5mm Red Light Set x 1
5. 3mm Orange Light Set x 2
|
| |
|
